T-Tech, Inc. announces our new 5 Axis Quick Mill™. The 5 Axis Quick Mill allows a mechanical engineer to make a metal part in the office in less than an hour. The five-axis motion allows for complex shapes and geometries developed by your design team with your CAD/CAM software. Purchase a 5 Axis Quick Mill, design a part, and make it in less than an hour! The 5 Axis Quick Mill is Made in the USA.
The 5 Axis Quick Mill has a work area of 8” x 8” x 8” with 17 automatic tool change locations, one tool point probe and a material touch probe. The 24,000 RPM spindle is liquid cooled with a temperature gauge allowing a pause running if the spindle gets hot. It has a three-horsepower spindle and due to the high RPM, you may program a light finishing cut with extreme accuracy. The tool tip sensor measures the length of each tool (TCP) for the setup, so the 5 Axis tool point offset software always knows where the tool is in relationship to your material in all axis at all times. The viewing camera is pointed at the work area so you can watch the mill work remotely on our web site application. The tool probe uses a wireless signal to detect probe contact.
The 5 Axis Quick Mill has intuitive software that runs on a Linux operating system. It uses an on-board computer system that has Linux CNC open-source software preinstalled and preconfigured for the controller software. Being open-source software, the cost for the software is Zero $. We have edited and branded some of the menus for simplicity and streamlining some operations.
The 5 Axis Quick Mill is completely self-contained. It will fit through a standard door. All you need to do is level the machine and plug it in. It requires a 220-volt, single phase, 30-amp outlet. Of course, you will need to put the coolant in the coolant container. We have supplied the wall outlet for your convenience and the proper power cord.
Technical Specifications
Due to continuous quality improvements, some technical specifications may change.
Hardware Features
- 5 Axis CNC true coordinated motion control.
- Servo Motor Motion Control with Closed Loop.
- 24,000 RPM Spindle, 3 Phase Drive, 3.0 HP/2.2 kw.
- ISO 20 Collet ER 32 tool holders for 17 position Automatic Tool Changer.
- It includes an automatic tool probe with wireless and LED interface.
- 6” long tool and 0.500” max tool shank.
- 8” x 8” x 8” work envelope.
- A axis 210 degrees of rotation.
- C axis 360 degrees of rotation.
- Precision Ground Ball Screw X, Y, Z axis.
- Protected covers over lead screws and ways.
- A & C Way axis break automatic or programable.
- Worm gear A & C axis.
- Standard T Slot rotary C axis.
- Precision flat plate for clamps or mighty bites.
- ER 40 through the table 1” collet for a circular part or tool mount.
- Chip tray for convenient extraction.
- Flood coolant filtration.
- Integrated enclosure and stand.
- Enclosed compressor.
- Automatic Door Closer.
Software Features
- Open-Source CNC Software.
- Linux operating system.
- EIA Standards G-Code and M-Code command set.
- A look ahead buffer.
- Remote camera internet observation.
- 3D graphics simulator.
Specifications
- Machine accuracy +- .0004”/ 0.01 mm.
- Machine repeatability +- .0002”/ 0.005 mm.
- Machine work area 8.0” x 8.0” x 8.0”/ 200 mm x 200 mm x 200 mm. *
- Machine Dimensions 240” x 180” x 180” / 600 mm x 450 mm x 450 mm. *
- Shipping Dimensions 200” x 200” x 400” / 500 mm x 500 mm x 1000 mm *
- Machine Weight 440 Lbs. / 200 Kg. *
- Shipping Weight 990 Lbs. / 450 Kg. *
- Standard Tool Package.
- Stand and Enclosure Dimensions 600” x 350” x 300” / 1500 mm x 900 mm x 750 mm. *
- Vibration pads and wheel set included with stand.
- Audible Noise at 1 meter = 72 db.
- 220 Volt, single phase, 50/60 Hz, 30-amp service.
- Coolant tank 2 Gallon / 8 Liter *.
- Quiet Compressor Clean, Dry compressed air at 125 psi / 7kps / 8 Gallon / 30-liter tank.
- Computer Linux, 8GB ram, 1T hard drive, Web enabled option.
Options
- Touch probing system option.
- Pendant manual axis drive with E-STOP
Common Applications
- Microwave Enclosures.
- RF Chassis.
- Injection Mold Making.
- Wax castings.
- Model making.
- Ice Sculptures.
Materials
Materials that may be fabricated are not limited to the following.
- Titanium
- Steal
- Stainless Steal
- Aluminum
- Brass
- Copper
- Delrin
- Lexan
- Polycarbonates
- FR4-G10
- Carbon Fiber
- Non-fired “green” ceramics
- Wood
Available Distribution
A complete list of distributors and sales representatives is on our website.
- Multiple quantity discounts are available.
- Tools, Supplies and Materials are available with overnight delivery.
- 90-day parts and labor warranty.
Extended warranty and annual calibration are available to meet your company’s quality standards and requirements. - CAD / CAM Software subscription is available.
Photo Gallery
Click for larger image.
